Hubbardton-forge 207858 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hubbardton-forge 207858. Hubbardton Forge 207858 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Assembly & Installation Instructions B117
For 20-7858 After Hours Wall Sconce Page 1 of 2
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19867 Rev B
For fixtures requiring assembly, please refer to assembly instructions before installation.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Mount Fixture to Wall (Figure 1)
Component Parts
A Wall Mounting Bracket
B Anchors (2)
C #10 Screws (2)
D Electric Box Cover
(for 4” Outlet box)
E #8 Black Screws (3)
F Fixture Assembly
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Carefully unpack the fixture from the carton.
2. Place the wall mounting bracket (A) over the electrical box using
one of the wiring holes provided being sure to hold it plum and
level. If using a single gang outlet box electric box, cover (D)
is not needed. Remove #8 black screw (E) from electric box
cover (D) and save for later use. Determine which electric box
cover (D) location works the best and attach to wall mounting
bracket (A). With a pencil, mark the location of all mounting
holes in the wall mount bracket on the wall behind.
IMPORTANT: Wall mounting bracket must be secured to a
solidly mounted to a framing member in at least two locations.
Do not depend on drywall anchors alone to support this fixture.
If in doubt, contact a qualified electrician.
Drill 1/4" holes in the locations marked on the wall. For holes
using anchors, place the tapered end of the anchors (B) into the holes and gently tap them flush to the
wall using a light weight hammer.
3. Thread the wires in the electrical box through the hole in the wall mounting bracket (A) while moving the bracket
into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
4. Hold the fixture assembly (F) close to the wall mounting bracket (A) and using suitable wire connectors (not
provided) connect fixture wires to supply wires (white to white, black to black, and bare copper or green to bare
copper or green). Ground the mounting bracket using the green ground wire fastened to the back of the fixture
assembly (F).
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
5. Carefully tuck all wires behind the fixture assembly (F) and inside the wall mounting bracket (A) and place the
fixture over the bracket so the holes in the top and bottom match the threaded holes in the wall mounting bracket
(A). Secure the fixture by threading the #8 black screws (E) through the holes in the fixture assembly (F) and into
the wall mounting bracket (B).
6. Install light bulb.
(continued)
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum watta
g
e noted on fixture. Use onl
y
recommended bulbs with fixture.
Figure 1
Vue de la page 0
1 2

Résumé du contenu

Page 1 - 19867 Rev B

Assembly & Installation Instructions B117 For 20-7858 After Hours Wall Sconce Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessories

Page 2

Assembly & Installation Instructions B117 For 20-7858 After Hours Wall Sconce Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessories

Commentaires sur ces manuels

Pas de commentaire