Hubbardton-forge 207765 Manuel d'utilisateur télécharger pdf

Installation Instructions B293

Ethos Sconce 20-7760D & 20-7765D Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

154 Route 30 South, Castleton, Vermont 05735

28305

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or

electrician

To Mount Fixture to Wall (Figure 1)

Component Parts

A Fixture Assembly

B Wall Mount Bracket

C Anchors (4)

D #10 Screws (4)

E #8 Black Screws (2)

F Rubber Washer (2)

G Green Ground Screw

H Cupped Washer

Caution: Be sure power is off at the main breaker

box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Center the wall mount bracket (B) over the

electrical box being sure to hold it plum and

level. With a pencil, mark the location of all

mounting holes in the wall mount bracket on

the wall behind.

IMPORTANT: Wall mount bracket must be

secured to a solidly mounted electrical box

and/or a framing member in at least two

locations. Do not depend on drywall anchors alone to support this fixture. If in doubt, contact a qualified

electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using

anchors, place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using

a light weight hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the

bracket into position. Using two machine screws (not provided), fasten the wall mount bracket (B) to the

electric box making sure that the bracket is level. Using the #10 screws (D), screw the bracket securely to

the wall. Be careful not to over-tighten or strip the anchors.

Note: A new electrical box comes with screws. When replacing a fixture, retain the existing screws for use

with the new fixture.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not

provided), connect fixture wires to supply wires (white to white or ribbed and black to black or smooth).

Ground the mounting bracket using the green ground screw (G) and cupped washer (H) to secure a pigtail

lead to the bracket and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

1 2

B293 1
28305 1

Résumé du contenu

Page 1 - 28305

Installation Instructions B293 Ethos Sconce 20-7760D & 20-7765D Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessories 154 R

Page 2

Installation Instructions B293 Ethos Sconce 20-7760D & 20-7765D Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessories 154 R

Modèles reliés 207760

Commentaires sur ces manuels

Pas de commentaire

Hubbardton-forge 207765 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hubbardton-forge 207765. Hubbardton Forge 207765 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 207760

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hubbardton-forge 207765