Hubbardton-forge 306014 Manuel d'utilisateur télécharger pdf

Assembly and Installation Instructions B111

For Direct Wire Wall-Mounted Sconces 30-6012 & 30-6014 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install Fixture (Figures 1 & 2)

Component Parts

A Black Screw (2)

B Rubber Washer

C Anchor (4)

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19773 RevA

D Ground

E Wall Mounting Bracket

F #10 Screw (4)

G Fixture

H Caulking Lip

Caution: Be sure power is off at the main breaker box prior

to installation.

1. Carefully unpack fixture from carton.

2. Place wall mounting bracket (E) over electrical box

being sure to hold it plum and level. With a pencil, mark

the location of all mounting holes in the bracket on wall.

Important: Wall mounting bracket must be secured to a

solidly mounted electrical box and/or a framing member

in at least two locations. Do not depend on drywall

anchors alone to support this fixture. If in doubt, contact

a qualified electrician.

Drill 1/4" holes in the locations marked on the wall. For

holes using anchors, place the tapered end of the anchors

using a light weight hammer.

3. Using the (4) #10 screws (F), screw the bracket securely

to the wall. Be careful not to over-tighten or strip the

anchors.

4. Move fixture (G) into position. Using suitable wire connectors (not provided), connect the fixture wires to the

supply wires; white to white, black to black, and bare copper or green to bare copper or green using ground (D)

screw with cupped washer.

Caution: Make sure wire connectors are twisted on securely and no bare

wires are exposed.

5. Apply a generous bead of a suitable caulking material to caulking lip (H)

on the fixture (not provided) (Figure 2).

6. Carefully tuck all wires behind the fixture, place fixture firmly against the

wall and fasten to wall mounting bracket (E) with black screw (A) and

rubber washer (B) on top.

7. Install 2

black screw (A) in bottom of fixture attaching to wall mounting

bracket (E).

8. To ensure a water tight seal, apply a thin bead of caulking around entire

perimeter of the fixture.

(

ure 1

)

(

ure

)

9. Restore electricity at the main breaker.

10. Install glass per instructions on next page.

(continued)

1 2

B111 1
19773 RevA 1

Résumé du contenu

Page 1 - 19773 RevA

Assembly and Installation Instructions B111 For Direct Wire Wall-Mounted Sconces 30-6012 & 30-6014 Page 1 of 2 CAUTION: FAILURE TO INSTALL THIS

Page 2

Assembly and Installation Instructions B111 For Direct Wire Wall-Mounted Sconces 30-6012 & 30-6014 Page 2 of 2 To Install Glass (Figures 3 &

Commentaires sur ces manuels

Pas de commentaire

Hubbardton-forge 306014 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hubbardton-forge 306014. Hubbardton Forge 306014 User Manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hubbardton-forge 306014