Hubbardton-forge 101283 Manuel d'utilisateur télécharger pdf

Assembly & Installation Instructions A160

For Berceau Seven-Light Chandelier 10-1283 Page 1 of 2 _

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21244

Install the Canopy (Figure 1)

Component Parts

A Crossbar

B Threaded Nipple

C Lag Screw (2)

D Lock Nut

E Canopy

F Loop Collar

G Threaded Loop

H Chain

I Fixture Loop

J Ground Screw

K Cupped Washer

L Hex Nut

Caution: This fixture must be supported independently of an outlet box.

Crossbar is designed to fit in the bottom of a standard metal 4” octagonal outlet

box.

Caution: Be sure power is off at the main breaker box prior to installation.

1. Drill two holes through the back of the outlet box and using two lag

screws (C) attach cross bar (A) to a structural member in the ceiling,

centering the crossbar in the outlet box. We've supplied lag screws

with your fixture; however, different materials and/or construction

methods may require different fasteners. If in doubt, contact a qualified

electrician.

2. Thread the nipple (B) into the crossbar (A).

3. Thread lock nut (D) and threaded loop (G) onto nipple, then place

canopy (E) over threaded loop and adjust nipple length to ensure a

snug canopy fit. Once the length is determined, set the canopy aside

and lock nipple position by tightening the locknut (D) against the

crossbar (A).

4. Attach one end of the chain (H) to the fixture loop (I).

5. Attach the other end of the chain to the threaded loop (F) and thread

the fixture wires through every other link of the chain (H) and up

through the threaded loop (G) and nipple (B) into the outlet box.

6. Using suitable wire connectors (not provided), connect fixture wires to

supply wires (white or ribbed side of fixture cord to white supply,

black or smooth side of fixture cord to black supply, and bare copper to

bare copper or green supply). Ground the crossbar (A) using the

ground screw (J), cupped washer (K) and hex nut (L) to secure

a pigtail lead to the crossbar. Push wires back into outlet box.

Caution: Make sure wire connectors are twisted on securely,

and no bare wire is exposed.

7. Slide the canopy up the chain and over the threaded loop (G), securing with loop collar (F). Make sure no wires

are pinched between the canopy (E) and the ceiling or crossbar (A).

(continued)

(Figure 1)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

1 2

Page 1 of 2 _ 1
Page 2 of 2 _ 2

Résumé du contenu

Page 1 - Page 1 of 2 _

Assembly & Installation Instructions A160 For Berceau Seven-Light Chandelier 10-1283 Page 1 of 2 _ Hand-Forged, Vermont-Made Lighting and

Page 2 - Page 2 of 2 _

Assembly & Installation Instructions A160 For Berceau Seven-Light Chandelier 10-1283 Page 2 of 2 _ Hand-Forged, Vermont-Made Lighting and

Commentaires sur ces manuels

Pas de commentaire

Hubbardton-forge 101283 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hubbardton-forge 101283. Hubbardton Forge 101283 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hubbardton-forge 101283