Hubbardton-forge 306520 Manuel d'utilisateur télécharger pdf

Installation Instructions B223

For Wall Sconce 30-6510, 30-6515 & 30-6520 Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

26600

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall

(Figure 1)

Component Parts

A Fixture Assembly

B Wall Mount Bracket

C Anchors (4)

D #10 Screws (4)

E #8 Black Screws (2)

F Rubber Washer (1)

G Green Ground Screw

H Cupped Washer

I Caulking Lip

Caution: Be sure power is off

at the main breaker box prior

to installation.

1. Carefully unpack the

fixture from the carton.

2. Center the wall mount

bracket (B) over the

electrical box being sure

to hold it plum and level.

With a pencil, mark the

location of all mounting

holes in the wall mount

bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical box and/or a framing member

in at least two locations. Do not depend on drywall anchors alone to support this fixture. If in doubt, contact a

qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,

place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light weight

hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten or

strip the anchors.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white or ribbed and black to black or smooth). Ground the

mounting bracket using the green ground screw (G) and cupped washer (H) to secure a pigtail lead to the bracket

and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

1 2

B223 1
26600 1

Résumé du contenu

Page 1 - 26600

Installation Instructions B223 For Wall Sconce 30-6510, 30-6515 & 30-6520 Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessories P.

Page 2

Installation Instructions B223 For Wall Sconce 30-6510, 30-6515 & 30-6520 Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessories P.

Modèles reliés 306515 | 306510 |

Commentaires sur ces manuels

Pas de commentaire

Hubbardton-forge 306520 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hubbardton-forge 306520. Hubbardton Forge 306520 User Manual [en] Manuel d'utilisatio

Résumé du contenu

Modèles reliés 306515 | 306510 |

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hubbardton-forge 306520