Hubbardton-forge 101283F Manuel d'utilisateur télécharger pdf

Assembly & Installation Instructions A161

For Berceau Seven-Light Chandelier 10-1283F Page 1 of 2 _

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21249

Install the Canopy (Figure 1)

Component Parts

A Crossbar

B Threaded Nipple

C Lag Screw (2)

D Lock Nut

E Canopy

F Loop Collar

G Threaded Loop

H Chain

I Fixture Loop

J Ground Screw

K Cupped Washer

L Hex Nut

Caution: Be sure power is off at the main breaker box prior to installation.

Caution: This fixture must be supported independently of an outlet box. Crossbar

is designed to fit in the bottom of a standard metal 4” octagonal outlet box.

1. Drill two holes through the back of the outlet box and using two lag screws

crossbar in the outlet box. We've supplied lag screws with your fixture;

however, different materials and/or construction methods may require

different fasteners. If in doubt, contact a qualified electrician.

2. Thread the nipple (B) into the crossbar (A).

3. Thread lock nut (D) and threaded loop (G) onto nipple, then place canopy

(E) over threaded loop and adjust nipple length to ensure a snug canopy fit.

Once the length is determined, set the canopy aside and lock nipple

position by tightening the locknut (D) against the crossbar (A).

4. Attach one end of the chain (H) to the fixture loop (I).

5. Attach the other end of the chain to the threaded loop (F) and thread the

fixture wires through every other link of the chain (H) and up through the

threaded loop (G) and nipple (B) into the outlet box.

6. Using suitable wire connectors (not provided), connect fixture wires to

supply wires (white or ribbed side of fixture cord to white supply, black or

smooth side of fixture cord to black supply, and bare copper to bare copper

or green supply). Ground the crossbar (A) using the ground screw (J),

cupped washer (K) and hex nut (L) to secure a pigtail lead to the crossbar.

Push wires back into outlet box.

Caution: Make sure wire connectors are twisted on securely, and no bare

wire is exposed.

7. Slide the canopy up the chain and over the threaded loop (G), securing

with loop collar (F). Make sure no wires are pinched between the canopy

(E) and the ceiling or crossbar (A).

(continued)

(Figure 1)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

1 2

Page 1 of 2 _ 1
Page 2 of 2 _ 2

Résumé du contenu

Page 1 - Page 1 of 2 _

Assembly & Installation Instructions A161 For Berceau Seven-Light Chandelier 10-1283F Page 1 of 2 _ Hand-Forged, Vermont-Made Lighting an

Page 2 - Page 2 of 2 _

Assembly & Installation Instructions A161 For Berceau Seven-Light Chandelier 10-1283F Page 2 of 2 _ Hand-Forged, Vermont-Made Lighting an

Commentaires sur ces manuels

Pas de commentaire

Hubbardton-forge 101283F Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hubbardton-forge 101283F. Hubbardton Forge 101283F User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hubbardton-forge 101283F