Hubbardton-forge 18352 Manuel d'utilisateur télécharger pdf

Assembly & Installation Instructions A60

For Adjustable Pendant Model 18-332 & 18-352 Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

16520 Rev C

To Complete Fixture Assembly

(Figures 1 & 2)

Component Parts

A Fixture Pipe

B Canopy Pipe

C Canopy

D Crossbar

E Ground Screw

F Threaded Stud (2)

G Knurl Balls (2)

H Plastic Clutch Sleeve

I Clutch

J Set Screw

K Locking Nut

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Thread the wires from the fixture pipe (A) into and through the canopy pipe (B) up

through the canopy (C).

3. Unscrew the clutch (I) from the canopy pipe (B); slide it across the wires and onto

the fixture pipe (A). Follow this with the plastic clutch sleeve (H), oriented so the

tapered end of the clutch sleeve nests in the clutch.

4. Slide the smaller pipe as far as necessary to give you the total length of the fixture

which you desire. Be careful not to scratch the pipe surfaces and to pull excess wire

up through the canopy. There must be a minimum 1-1/2" of inner pipe inside

the outer pipe. There must be a minimum of 6-1/2" between the clutch and the

locking nut to allow for bulb replacement. Hand-tighten the clutch to

temporarily hold this adjustment. At this point the adjustment is not securely

fastened; do not depend on it to permanently hold the fixture.

Important: To ensure full connection strength, be sure the tapered end of the

plastic clutch sleeve is oriented toward the clutch when assembled and securely

tighten set screw (Figure 2).

5. Thread studs (F) through appropriate holes in crossbar (D) to match holes in

canopy (C).

6. Using two machine screws (not provided), fasten the crossbar (C) to the electric

box.

Note: A new electric box comes with screws. When replacing a fixture, retain the

existing screws for use with the new fixture.

7. Using suitable wire connectors (not provided) connect fixture wires to supply

(white to white or ribbed and black to black or smooth). Connect all ground wires

to green ground screw (E).

Caution: Make sure wire connectors are twisted on securely, and no bare wire is

exposed.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

This illustration represents a typical

fixture and may not match every style.

1 2

A60 1
16520 Rev C 1

Résumé du contenu

Page 1 - 16520 Rev C

Assembly & Installation Instructions A60 For Adjustable Pendant Model 18-332 & 18-352 Page 1 of 2 Hand-Forged, Vermont-Made Lighting

Page 2

Assembly & Installation Instructions A60 For Adjustable Pendant Model 18-332 & 18-352 Page 2 of 2 Hand-Forged, Vermont-Made Lighting

Modèles reliés 18332

Commentaires sur ces manuels

Pas de commentaire

Hubbardton-forge 18352 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hubbardton-forge 18352. Hubbardton Forge 18352 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 18332

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hubbardton-forge 18352