Hubbardton-forge 207525 Manuel d'utilisateur télécharger pdf

Installation Instructions B128

For Ellipse Sconces 207525, 207525F, 207535 & 207535F Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21028

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1 & 2)

Component Parts

A Wall Mount Bracket

B Anchors (4)

C #10 Screws (4)

D Fixture Assembly

E #8 Black Screws (4)

F Green Ground Screw

G Cupped Washer

H Wireway Cover

I Barrel Knob (2)

Caution: Be sure power is off at the main

breaker box prior to installation.

1. Carefully unpack the fixture from the

carton.

2. Center the wall mount bracket (A) over

the electrical box being sure to hold it

plum and level. With a pencil, mark the

location of all mounting holes in the w

mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to

a solidly mounted electrical box and/or a framing

member in at least two locations. Do not depend on

drywall anchors alone to support this fixture. If in doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,

place the tapered end of the anchors (B) into the holes and gently tap them flush to the wall using a light weight

hammer.

This illustration represents a typical fixture

and may not match every style.

(Figure 1)

all

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or

strip the anchors.

4. Thread the black # 8 screws (E) up through the holes in the top of the wall mount bracket (A). Leave the bottom

screws out for now.

5. Remove the wireway cover (H) and save for later installation.

6. Hold the fixture assembly (D) close to the wall mount bracket (A) ground the mounting bracket using the green

ground screw (F) and cupped washer (G) to secure a pigtail lead to the bracket.

(continued)

1 2

B128 1
21028 1

Résumé du contenu

Page 1 - 21028

Installation Instructions B128 For Ellipse Sconces 207525, 207525F, 207535 & 207535F Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Acces

Page 2

Installation Instructions B128 For Ellipse Sconces 207525, 207525F, 207535 & 207535F Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Acces

Commentaires sur ces manuels

Pas de commentaire

Hubbardton-forge 207525 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hubbardton-forge 207525. Hubbardton Forge 207525 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hubbardton-forge 207525